View B133EW01-V1_2098257.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

au optronics corporation b133e w 01 v1 product specification document v ersion 0.2 1 ( v ) pr eli m i n a r y s pecificatio n s ( ) fi n al s pecificatio n s m od u le 13.3 w x g a co l or tf t -l cd m od el na m e b133e w 01 v1 c u st o m e r da te c h ecke d & a pp r o v e d b y no t e : t h i s s pec i f i cat i on i s s ub j ec t t o c hange w it hou t no tic e. a pp r o v e d b y da te p r e p a r e d b y m dbu m arket i ng d i v i s i on / au optron i cs corporat i on www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 2 contents 1. handling precautions..............................................................................................................4 2. general description.................................................................................................................5 2.1 display characteristics......................................................................................................5 2.2 optical characteristics.......................................................................................................7 3. functional block diagram.....................................................................................................12 4. absolute maximum ratings..................................................................................................13 4.1 tft lcd module..............................................................................................................13 4.2 backlight unit...................................................................................................................13 4.3 absolute ratings of environment.....................................................................................13 5. electrical characteristics.......................................................................................................14 5.1 tft lcd module..............................................................................................................14 5.2 backlight unit...................................................................................................................16 6. signal characteristic.............................................................................................................18 6.1 pixel format image..........................................................................................................18 6.2 the input data format.......................................................................................................19 6.3 signal description............................................................................................................21 6.4 interface timing................................................................................................................23 6.5 power on/off sequence...............................................................................................24 7. connector & pin assignment................................................................................................25 7.1 tft lcd module..............................................................................................................25 7.2 backlight unit...................................................................................................................25 7.3 signal for lamp connector...............................................................................................25 8. vibration and shock test......................................................................................................26 8.1 vibration test...................................................................................................................26 8.2 shock test spec:..............................................................................................................26 9. reliability................................................................................................................................27 10. mechanical characteristics.................................................................................................28 10.1 lcm outline dimension.................................................................................................28 10.2 screw hole depth and center position..........................................................................31 11. shipping and package.........................................................................................................32 11.1 shipping label format...................................................................................................32 11.2. carton package.............................................................................................................33 11.3 shipping package of palletizing sequence.....................................................................33 12. appendix: edid description................................................................................................34 www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 3 record of revision version and date page old description new description remark 0.1 2006/1/03 all first edition for customer 0.2 2006/3/7 12 ammend typo and drawing www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 4 1. handling precautions 1) since front polarizer is easily damaged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the ccfl reflector edge. instead, press at the far ends of the cfl reflector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an enclosure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local ordinances or regulations for disposal. 13) small amount of materials having no flammability grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source(, iec60950 or ul1950), or be applied exemption. 14) the lcd module is designed so that the ccfl in it is supplied by limited current circuit(iec60950 or ul1950). do not connect the ccfl in hazardous voltage circuit. www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 5 2. general description b133ew01 v1 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen format is intended to support the wxga (1280(h) x 800(v)) screen and 262k colors (rgb 6-bits data driver). all input signals are lvds interface compatible. inverter of backlight is not included. b133ew01 v1 is designed for a display unit of notebook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 337.8 (13.3 w ) active area [mm] 286.08 (h) x 178.8 (v) pixels h x v 1280x3(rgb) x 800 pixel pitch [mm] 0.2235 x 0.2235 pixel arrangement r.g.b. vertical stripe display mode normally white white luminance (i ccfl =6.0ma) note: i ccfl is lamp current [cd/m 2 ] 250 typ. (5 points average) 210 min. (5 points average) ( note1 ) luminance uniformity 1.25 max. (5 points) contrast ratio 300 typ optical rise time/fall time [msec] 25 typ. nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] 4.8 max.(without inverter) weight [grams] 350 typ. physical size [mm] 299.5 max. (w) x 195.5 max. (h) x 5.5 electrical interface 1 channel lvds surface treatment anti-glare, hardness 3h, reflectance 2.5 % support color 262k colors ( rgb 6-bit ) temperature range operating storage ( non - operating) [ o c] [ o c] 0 to +50 -20 to +60 rohs compliance rohs compliance www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 6 www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 7 2.2 optical characteristics the optical characteristics are measured under stable conditions at 25 (room temperature): item unit conditions min. typ. max. note white luminance i ccfl =6.0ma [cd/m 2 ] 5 points average 210 250 - 1, 4, 5. [degree] [degree] horizontal (right) cr = 10 (left) 40 40 45 45 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) 10 30 25 35 - - 8 luminance uniformity 5 points 1.25 1 luminance uniformity 13 points 1.50 2 cr: contrast ratio 200 300 - 6 cross talk % 4 7 [msec] rising - 16 22 [msec] falling - 9 13 response time [msec] rising + falling 25 35 8 red x 0.565 0.595 0.625 red y 0.315 0.345 0.375 green x 0.29 0.32 0.35 green y 0.525 0.555 0.585 blue x 0.125 0.155 0.185 blue y 0.115 0.145 0.175 white x 0.283 0.313 0.343 color / chromaticity coordinates (cie 1931) white y 0.299 0.329 0.359 2,8 note 1: 5 points position (display area : 286.08 (h) x 178.8 (v)mm) www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 8 12 3 45 h/4 h/4 h/4 h/4 h w w/4 w/4 w/4 w/4 note 2: 13 points position w/4 w w/4 h h/4 h/4 h/4 h/4 7 9 10 w/4 1 8 w/4 10 10 10 10 2 3 13 12 4 5 6 11 note 3: the luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the minimum test point luminance w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five points w5 = minimum brightness of five points www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 9 note 4: measurement method the lcd module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after lighting backlight for 30 minutes in a stable, windless and dark room. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the point x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following formula. center of the scree n tft - lcd 50 cm photo detector lcd panel field=2 contrast ratio (cr)= brightness on the white state brightness on the black state www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 10 note 7 definition of cross talk (ct) ct = | y b C y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 8: definition of response time: the output signals of bm-7 or equivalent are measured when the input signals are changed from black to white (falling time) and from white to black (rising time), respectively. the response time interval between the 10% and 90% of amplitudes. refer to figure as below. "black" tr tf "white" "white" 0 % 10 % 90 % 100 % optical response www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 11 note 8. definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 12 3. functional block diagram the following diagram shows the functional block of the 13. 3 inches wide color tft/lcd module: tft array/cell vdd lcd controller lcd drive board backlight unit 1280(r/g/b) x 3 x 800 gnd dc-dc converter ref circuit y-driver x-driver rxin0 rxin1 rxin2 rxclkin (4 pairs lvds) herose : df19l-20p-1h mating housing df-19g-20s-1sd jst bhsr-02vs- 1 mating type sm02b-bhss-1- tb lamp connector(2pin) lcd connector(20 pin) www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 13 4. absolute maximum ratings absolute maximum ratings of the module is as following: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of backlight unit item symbol min max unit conditions ccfl current iccfl - 6.5 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 3 operation humidity hop 5 95 [%rh] note 3 storage temperature tst -20 +60 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to auo iis(incoming inspection standard). twb=39 c operating range storage range www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 14 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power 0.8 [watt] note 1 idd idd current 200 2500 [ma] note 1 i rush inrush current 1500 [ma] note 2 vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p note 1 : maximum measurement condition black patterm note 2 measure condition q3 ao6402 g d 2 s d 1 d 5 d 6 c3 0.01uf/25v c2 1uf/25v c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 f1 vr1 47k +12.0v vcc sw1 sw mag-spst 1 2 (lcd module input) (high to low) control signal r2 1k r2 1k r1 47k +3.3v 90% 10% vin rising time 0v 3.3v 0.5ms www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 15 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold (vcm=+1.2v) 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 [mv] vcm differential input common mode voltage 1.0 1.5 [v] note: lvds differential voltage www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 16 5.2 backlight unit parameter guideline for ccfl inverter parameter min typ max units condition white luminance 5 points average 210 250 - [cd/m 2 ] (ta=25 ) ccfl current(i ccfl ) 2.0 6.0 7.0 [ma] rms (ta=25 ) note 2 ccfl frequency(f ccfl ) 50 62 70 [khz] (ta=25 ) note 3,4 ccfl ignition voltage(vs) 1315 [volt] rms (ta= 0 ) note 5 ccfl ignition voltage(vs) 1095 [volt] rms (ta= 25 ) note 5 ccfl voltage (reference) (v ccfl ) 608 640 672 [volt] rms (ta=25 ) note 6 ccfl power consumption (p ccfl ) - 3.8 4.2 [watt] (ta=25 ) note 6 note 1: typ are auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to check safety circuit very carefully. impedance of ccfl, for instance, becomes more than 1 [m ohm] when cfl is damaged. *4 generally, ccfl has some amount of delay time after applying kick-off voltage. it is recommended to keep on applying kick-off voltage for 1 [sec] until discharge. *5 ccfl discharge frequency must be carefully chosen so as not to produce interfering noise stripes on the screen. *6 reducing ccfl current increases ccfl discharge voltage and generally increases ccfl discharge frequency. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. note 2: it should be employed the inverter which has duty dimming , if iccfl is less than 4ma. note 3: ccfl discharge frequency should be carefully determined to avoid interference between inverter and tft lcd. note 4: the frequency range will not affect to lamp life and reliability characteristics. www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 17 note 5: ccfl inverter should be able to give out a power that has a generating capacity of over 1,430 voltage. lamp units need 1,400 voltage minimum for ignition. note 6: calculator value for reference (i ccfl v ccfl =p ccfl ) note 7: requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. it shall help increase the lamp lifetime and reduce leakage current. a. the asymmetry rate of the inverter waveform should be less than 10%. b. the distortion rate of the waveform should bewithin 2 10%. * inverter output waveform had better be more similar to ideal sine wave. www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 18 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 0 1 1278 1279 1st line 800th line www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 19 6.2 the input data format signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the typical frequency is 68.9 mhz.. the signal is used to strobe the pixel data and de signals. all pixel data shall be valid at the falling edge when the de signal is high. de display timing this signal is strobed at the falling edge of rxclkin. when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync the signal is synchronized to rxclkin . hs horizontal sync the signal is synchronized to rxclkin . note: output signals from any system shall be low or high-impedance state when vdd is off. www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 20 www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 21 6.3 signal description/pin assignment lvds is a differential signal technology for lcd interface and high speed data transfer device. pin# signal name description 1 gnd ground 2 vdd +3.3v power supply 3 vdd +3.3v power supply 4 v edid +3.3v edid power 5 nc no connection (reserve for auo test) 6 clk edid edid clock input 7 data edid edid data input 8 rxin0- lvds differential data input(r0-r5, g0) 9 rxin0+ lvds differential data input(r0-r5, g0) 10 gnd ground 11 rxin1- lvds differential data input(g1-g5, b0-b1) 12 rxin1+ lvds differential data input(g1-g5, b0-b1) 13 gnd ground 14 rxin2- lvds differential data input(b2-b5, hs, vs, de) 15 rxin2+ lvds differential data input(b2-b5, hs, vs, de) 16 gnd ground 17 rxclkin- lvds differential clock input 18 rxclkin+ lvds differential clock input 19 gnd ground 20 gnd ground www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 22 note1: start from right side note2: input signals shall be low or high-impedance state when vdd is off. internal circuit of lvds inputs are as following. the module uses a 100ohm resistor between positive and negative data lines of each receiver input r r r r lvds receiver signal input pin no. 9 11 12 14 15 17 18 8 rxin0+ rxin0- rxin1+ rxin1- rxin2+ rxin2- rxclkin+ rxclkin- 20 1 n c g n d connector www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 23 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1280x800 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - 50 60 - hz clock frequency 1/ t clock 50 68.9 80 mhz period t v 803 816 832 active t vd 800 800 800 vertical section blanking t vb 3 16 32 t line period t h 1302 1408 1700 active t hd - 1280 - horizontal section blanking t hb 22 128 420 t clock note : de mode only 6.4.2 timing diagram dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 24 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. power sequence timing value parameter min. typ. max. units t1 0.5 - 10 (ms) t2 0 - 50 (ms) t3 0 - 50 (ms) t4 400 - - (ms) t5 200 - - (ms) t6 200 - - (ms) t7 0 - 10 (ms) t4 t3 t2 t5 valid data t1 10% 90% 10% 90% t6 t 7 power supply vdd lvds interface backlight on www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 25 7. connector description physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer hirose or compatible type / part number df-19la-20p-1h or compatible mating housing/part number df19g-20s-1sd or compatible 7.2 backlight unit physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 7.3 signal for lamp connector pin # cable color signal name 1 red lamp high voltage 2 white lamp low voltage www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 26 8. vibration and shock test 8.1 vibration test test spec: l test method: non-operation l acceleration: 1.5g , sine wave l frequency: 10 - 500hz random l sweep: 30 minutes each axis (x, y, z) 8.2 shock test spec: test spec: l test method: non-operation l acceleration: 200 g , half sine wave l active time: 2 ms l pulse: x,y,z .one time for each side www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 27 9. reliability items required condition note temperature humidity bias 40 /90%,300hr high temperature operation 60 /dry,300hr low temperature operation 0 ,300hr on/off test 25 , on/30 sec. off/30sec., 10,000 cycles) hot storage 60 /35% rh ,250 hours cold storage -20 /50% rh ,250 hours thermal shock test -20 /30 min ,60 /30 min 100cycles hot start test 50 /1 hr min. power on/off per 5 minutes, 5 times cold start test 0 /1 hr min. power on/off per 5 minutes, 5 times shock test (non-operating) 200g, 2ms, half-sine wave vibration test (non-operating) sine-wave vibration, 1.5 g zero-to-peak, 10 to 500 hz, 30 mins in each of three mutually perpendicular axes. esd contact : 8kv/ operation air : 15kv / operation note 1 room temperature test 25 , 2000hours, operating with loop pattern note1: according to en61000-4-2 , esd class b: some performance degradation allowed. no data lost . self-recoverable. no hardware failures. note2: ccfl life time: 10,000 hours minimum under normal module usage. note3: mtbf (excluding the ccfl): 30,000 hours with a confidence level 90% www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 28 10. mechanical characteristics 10.1 lcm outline dimension www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 29 www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 30 www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 31 10.2 screw hole depth and center position screw hole minimum depth, from side surface =2.5 mm (see drawing) screw hole center location, from front surface = 2.8 0.2mm (see drawing) screw torque: maximum 2.1 kgf-cm www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 32 11. shipping and package 11.1 shipping label format tbd note 1: ic combination control code h/w tsb/nt (gate/source) oaxxx oa nt/nt(gate/source) 1axxx 1a www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 33 11.2. carton package the outside dimension of carton is tbd 11.3 shipping package of palletizing bottom cardboard top cardboard stretch film corner angle wooden pallet pet band label www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 34 12. appendix: edid description 12. appendix: edid description address address field name & comments value value value (decimal) (hex) (hex) (bin) (dec) 0 0 header 00 00000000 0 1 1 ff 11111111 255 2 2 ff 11111111 255 3 3 ff 11111111 255 4 4 ff 11111111 255 5 5 ff 11111111 255 6 6 ff 11111111 255 7 7 00 00000000 0 8 8 eisa manuf. code lsb ( 3 character id = app) 06 00000110 6 9 9 compressed ascii 10 00010000 16 10 0a product code = 5c 5c 01011100 92 11 0b hex, lsb first = 9c 9c 10011100 156 12 0c 32-bit serial # 00 00000000 0 13 0d 00 00000000 0 14 0e 00 00000000 0 15 0f 00 00000000 0 16 10 week of manufacture (week 13) 0d 00001101 13 17 11 year of manufacture (2006) 10 00010000 16 18 12 edid structure ver # = 1 01 00000001 1 19 13 edid revision # = 3 03 00000011 3 20 14 video input definition = digital input, non tmds crgb 80 10000000 128 21 15 max h image size = 29 cm 1d 00011101 29 22 16 max v image size = 18 cm 12 00010010 18 23 17 display gamma = 2.2 78 01111000 120 24 18 feature support (dpms) = active off, rgb color 0a 00001010 10 25 19 red/green low bits 50 01010000 80 26 1a blue/white low bits c5 11000101 197 27 1b red x , red x = 0.595 98 10011000 152 28 1c red y , red y = 0.345 58 01011000 88 www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 35 29 1d green x , green x = 0.32 52 01010010 82 30 1e green y , green y = 0.555 8e 10001110 142 31 1f blue x , blue x = 0.155 27 00100111 39 32 20 blue y , blue y = 0.145 25 00100101 37 33 21 white x , white x = 0.313 50 01010000 80 34 22 white y , white y = 0.329 54 01010100 84 35 23 established timing 1 00 00000000 0 36 24 established timing 2 00 00000000 0 37 25 manufacturer's timings 00 00000000 0 38 26 standard timing #1 was not used 01 00000001 1 39 27 01 00000001 1 40 28 standard timing #2 was not used 01 00000001 1 41 29 01 00000001 1 42 2a standard timing #3 was not used 01 00000001 1 43 2b 01 00000001 1 44 2c standard timing #4 was not used 01 00000001 1 45 2d 01 00000001 1 46 2e standard timing #5 was not used 01 00000001 1 47 2f 01 00000001 1 48 30 standard timing #6 was not used 01 00000001 1 49 31 01 00000001 1 50 32 standard timing #7 was not used 01 00000001 1 51 33 01 00000001 1 52 34 standard timing #8 was not used 01 00000001 1 53 35 01 00000001 1 54 36 detailed timing/monitor bc 10111100 188 55 37 1280x800 @60hz : pixel clock =71 mhz 1b 00011011 27 56 38 hor active=1280 pixels 00 00000000 0 57 39 hor blanking=16 pixels a0 10100000 160 58 3a 50 01010000 80 59 3b vertcal active=800 lines 20 00100000 32 60 3c vertical blanking=23lines 17 00010111 23 61 3d 30 00110000 48 62 3e h sync. offset=48 pixels 30 00110000 48 63 3f h sync. width=32 pixels 20 00100000 32 www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 36 64 40 v sync. offset=3 lines 36 00110110 54 65 41 v sync. width=6 lines 00 00000000 0 66 42 h image size= 286.08 mm 1e 00011110 30 67 43 v image size = 178.8 mm b3 10110011 179 68 44 10 00010000 16 69 45 no horizontal border 00 00000000 0 70 46 no vertical border 00 00000000 0 71 47 non-interlaced, normal display, no stereo, digital separate sync, h/v pol negatives 18 00011000 24 72 48 detailed timing/monitor 00 00000000 0 73 49 descriptor #3 00 00000000 0 74 4a 00 00000000 0 75 4b 01 00000001 1 76 4c version 00 00000000 0 77 4d auo definition 06 00000110 6 78 4e auo definition 10 00010000 16 79 4f link type (lvds link,msb justified) 20 00100000 32 80 50 pixel and link component format (6-bit panel interface) 00 00000000 0 81 51 panel features (no inverter) 00 00000000 0 82 52 00 00000000 0 83 53 00 00000000 0 84 54 00 00000000 0 85 55 00 00000000 0 86 56 00 00000000 0 87 57 00 00000000 0 88 58 0a 00001010 10 89 59 20 00100000 32 90 5a detailed timing/monitor 00 00000000 0 91 5b descriptor #3 00 00000000 0 92 5c b133ew01 v1 00 00000000 0 93 5d fe 11111110 254 94 5e 00 00000000 0 95 5f b 42 01000010 66 96 60 1 31 00110001 49 www..net
au optronics corporation b133ew01 v1 product specification document version 0.2 37 97 61 3 33 00110011 51 98 62 3 33 00110011 51 99 63 e 45 01000101 69 100 64 w 57 01010111 87 101 65 0 30 00110000 48 102 66 1 31 00110001 49 103 67 20 00100000 32 104 68 v 56 01010110 86 105 69 0 30 00110000 48 106 6a 0a 00001010 10 107 6b 20 00100000 32 108 6c detailed timing/monitor 00 00000000 0 109 6d descriptor #4 00 00000000 0 110 6e color lcd 00 00000000 0 111 6f fc 11111100 252 112 70 00 00000000 0 113 71 c 43 01000011 67 114 72 o 6f 01101111 111 115 73 l 6c 01101100 108 116 74 o 6f 01101111 111 117 75 r 72 01110010 114 118 76 space 20 00100000 32 119 77 l 4c 01001100 76 120 78 c 43 01000011 67 121 79 d 44 01000100 68 122 7a 0a 00001010 10 123 7b 20 00100000 32 124 7c 20 00100000 32 125 7d 20 00100000 32 126 7e extension flag = 00 00 00000000 0 127 7f checksum b7 10110111 183 www..net

▲Up To Search▲

Price & Availability of B133EW01-V1

	To Download B133EW01-V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .